YH-GRC Fertilizer Granule Rotary Coating Machine
Drum granulation equipment is a molding machine that can make the material into a specific shape. The primary mode of work is wet granule granulation through a certain amount of water or steam so that the essential fertilizer in the cylinder body after humidification whole chemical reaction, in a specific liquid condition, with the help of cylinder rotation movement, so that the material particles between the squeeze pressure agglomeration into balls. The cylinder body of this machine is lined with a special rubber sheet or acid-resistant stainless steel liner, which can automatically remove scars and tumors and cancel the traditional device. Drum type granulation machine, the machine into the steam, gas ammonia or add phosphoric acid or nitrogen solution, phosphorus ammonia slurry, heavy calcium slurry, chemical reaction, and heat in the barrel to complete the compound fertilizer granulation process; Or add a small amount of water in the compound fertilizer cold granulation process. The material to be pelleted through the rotation of the cylinder, no material in the cylinder to produce a rolling wheel, in specific humidity, temperature, cohesion into balls, complete the pelleting process. The drum pelleting machine is a new generation of rotary drum pelleting machine developed by the staff of our company with many years of experience in compound fertilizer production. The device has a beautiful appearance, simple operation, low energy consumption, long life, uniform drying, convenient maintenance, and other characteristics; it is domestic, more advanced granulation equipment, and the product is suitable for cold, hot granulation, and high, medium, low concentration of compound fertilizer mass production, the product has been throughout.
Rotary Drum Cooler adopts a heating exchange method to cool materials. It is equipped with welded steel spiral scraping wings in front of the tube, a lifting board at the end of the rotary body, and an auxiliary piping system at the feed end of the cooling machine. The main motor drives the belt and pulley, and the drive shaft is put in motion through the reducer. Using a dryer together can greatly improve the cooling rate, reduce labor intensity and quality, remove moisture, and reduce the grain temperature of fertilizer. At the same time, it can also be used for cooling powder and other granule materials.
1. Wide applicability, available for many kinds of materials.
2. Simple operation, stable performance;
3. Low investment, high efficiency, and capacity;
4. Low cost in maintenance.
1. For chemical, miners, metallurgical and other industries: such as ores, slag, coal, metal powder, clay, kaolin, etc.
2. For agriculture, feed, and fertilizer industries: straw, grass, leaves, fish meal, corn sauce, aquatic wastes, food factory waste, etc.
3. For powdery, granular material dryer: such as crystals, precipitated calcium carbonate, activated clay, phosphorus slag, etc.
4. For the materials that require low-temperature drying.
|
Model |
Inner Diameter (mm) |
Length (mm) |
Production rate (t/h) |
Rotation speed (rpm) |
Power (kw) |
|
YH-DG100 |
1000 |
6000 |
2 |
13 |
7.5 |
|
YH-DG150 |
1500 |
6000 |
4 |
13 |
11 |
|
YH-DG200 |
2000 |
8000 |
10 |
11 |
15 |
|
YH-DG240 |
2400 |
10000 |
20 |
11 |
37 |
1.Bearing bears all the machine's load, so good lubrication has a great relationship to the bearing life, which directly affects the machine's service life and running rate, so the injected lubricating oil must be clean, and the seal must be good. The central oiling place of the machine (1) rotating bearing (2) rolling bearing (3) all gears (4) movable bearing, sliding plane.
2.The newly installed tire is easy to lose and must be checked frequently.
3. Paying attention to the work of all parts of the machine is normal.
4. Check the wear degree of easy-to-wear parts, and replace worn parts at any time.
5.The bottom frame plane of the portable device should go out of dust and other things so that the machine can not be broken when the movable bearing can not move on the bottom frame, as to cause serious accidents.
6.If the bearing oil temperature rises, it should be stopped immediately to check the cause to exclude.
7. If there is an impact sound when the rotating gear runs, it should be stopped immediately to check and exclude.
